HET L-39 Albatros – Breitling 2010

The HET L-39 Albatros is a high performance EDF Jet with fiberglass fuselage and foam/balsa wings suitable for 90mm Fan units such as the Schuebeler DS-51 or WeMoTec Midi Fan Pro.
A turbine conversion to JetCat P-20 or Lambert T25 (see similar conversion done with the JTM Hawk) can be done. Please check with us on suitable turbines, pipes and accessories.
The model features a fiberglass fuselage and foam/balsa wings with retract hard points pre-installed in the nose and retract hatches.
The model comes completely pre-painted.
The Model features flaps.
This model is truly ARF with all the major work done for you.

HET Flying Wing 1.8m + Prop Yellow

The HET Flying Wing in yellow color is a 1.8 meter wingspan powered glider for slope, ridge and thermals.
Combined with a brush less motor and the included 10×6 folding prop and spinner, the HET Flying Wing is capable of powerful climbs.
The HET Flying Wing features a fiberglass fuselage and foam/balsa sheeted wings. The Model completely build and requires a minimum of assembly.
With it’s large speed envelope the Wing is suitable for beginners as well as experienced pilots looking for a aerobatic glider with good wind penetration.
The Wing can be build as glider or powered glider.

HET F-16 Thunderbirds

The 3rd Jet for a 90mm Fan unit from HET-RC.
Unlike the other 2 models (Sniper 90 and F-18), the HET-RC F-16 features a epoxy fiberglass fuselage resulting in a lighter body and more chip resistant surface.
The F-16 is a available in 4 distinct color schemes, Edwards AFB, General Dynamics, Gray and Thunderbirds.
The model is fully prepared for a retractable landing gear (see options below) and allows the installation of working gear doors. Powered by 8-10S and with its included wingtip missiles, this model will be the star at every flying site.

AirPower Air Control System Kit – PRO

A great way to save some $$$. This Air Control System Kit Pro supports any Air Retract, Door and brake system
Complete with:
- 2x Airpower EV-2U Dual Action Valves
- 1x AirPower EV-1U – Brake Valve
- 1x Digit Dual Air Gauge
- 2x Air System Fill Valve with Chuck
- 10x Barbed Airline Fittings
- 4x Airpower 1/8″ / 3 mm Air Tubing Mount
- 10meter of Airpower 1/8″ Air Line
- 2x Airpower Air Tanks
this complete installation kit leaves no desires open.

HET Retract Set 90size (L-39)

The HET-RC L-39 Retracts are specially designed for the HET-RC L-39 Albatros composite EDF Jets. The set comes complete with air tank, hose and valves. These retracts come with oleo struts mounts suitable for the optional available HET-RC L-39 Oleo Struts.

HET L-39 Oleo Struts

Oleo Struts specially designed for the HET L-39 90 size EDF Jet. Add scale realism in looks and function to your model air plane. Whether you use fixed or retractable landing gears, these struts can be fitted. Helps to smoothen landings and improves ground handling, especially on grass fields. Package includes 2 trailing main gear oleo units with wheels and one trailing nose oleo strut with fork mounted wheel

HET Flying Wing 1.8m + Prop Red

The HET Flying Wing in yellow color is a 1.8 meter wingspan powered glider for slope, ridge and thermals.
Combined with a brush less motor and the included 10×6 folding prop and spinner, the HET Flying Wing is capable of powerful climbs.
The HET Flying Wing features a fiberglass fuselage and foam/balsa sheeted wings. The Model completely build and requires a minimum of assembly.
With it’s large speed envelope the Wing is suitable for beginners as well as experienced pilots looking for a aerobatic glider with good wind penetration.
The Wing can be build as glider or powered glider.

Festo Y-Tube fitting

Festo Y Fitting for 3mm and 4mm tubing.
Suitable for Air, Gas and Kerosene.

Festo Tee Tube fitting

Festo Tee Fitting for 3mm and 4mm tubing.
Suitable for Air, Gas and Kerosene.

Festo PUN-H Tubing

Festo 3mm and 4mm PUN-H tubing.
Suitable for Air, Gas and Kerosene.

This months special offer:
HET-RC F-86 Sabre in gray or airbrush color.

Offer valid till July 31st or till stocks last.

Click here for details: Airbrush Color

Click here for details: Gray Color

July 2011 Desktop Wallpaper

July 2011 features another photo taken during the 2008 TopGun Event in Lakeland Florida.
This time we feature a BVM Ultra Bandit captured during a knife edge flyby.

AirPower RA-215 Retract Main and Nose

AirPower Models are pleased to present their all new retract units.
Made from Anodised aluminium these units feature air up and air down operation and are intended to use in models from 9kg / 20lbs up to 20kg / 45 lbs in weight. Designed to be retro fitted in many of today’s sport models these units are able to withstand operation from grass and tarmac fields.
The main pivot block is made from high quality 7075 aluminium and machined to accept a 1/2” oleo strut. Retained in a clamp type mount that ensures a secure fixing with less chance of the leg rotating. The pivot pin is deliberately oversized in a effort to make all three units more rugged. The nose retract come as standard with the steering mechanism pre fitted as well as the straightening spring, although this can easily be removed and replaced with a 1/2 inch Oleo leg.
The RA-215 are available as singular units or as a complete kit of 3 units.

AirPower RA-250 Retract Main and Nose

AirPower’s RA-250 retract offers an ultra low profile that is only 27mm in height. This retract is able to take a 7/16″ diameter Strut. Also available is a standard gear wire in 3/16″ for Main Gears.
The Retract is constructed out of high quality aircraft grade 6061-T6 & 7075 aluminum. The RA-250 Retracts is designed to replace other manufacturers retract systems and are the strongest retractable landing gear in the industry for this size.

Grumania FOD for JetCat P20-SE

This FOD screen is special design for use with a JetCat P20-SE or similar size turbine engine.

Tamjets E-flite Spark Retract Set

Full electric retract set for the CARF Spark.
The Tamjets / E-flite retract set is based on the original E-flite 60 – 120 Tricycle Electric Retracts set. However in order to support the weight of the Spark and make the retract unit more durable in general, Tamjets replaced the original E-flite trunion with an stronger unit machined out of high strength aluminum.
In addition this new trunion is now capable of utilizing the proven Tamjets trailing oleo struts for the CARF Spark.
The set further includes a set of Tamjet TJ Pro-Lite wheels and brakes to complete the combo.

AirPower 5mm Wire Struts Wheels & Brake Set

High performance inflatable model tire with pneumatic brake and 5mm Wire strut + adapter.
Inflatable tire with metal rim. The tires comes with precision ball bearings (6mm).
Tire is replaceable.
Suitable for all retract mechanics with 5mm wire adapter (wire strut is included in the set)

AirPower Wheel Spares

Various spare parts for Airpower Wheels:
- AirPower 70~85mm Wheel Rubber Seals
- AirPower 70~85mm Inflation Seals
- AirPower Replacement 90 deg Air Fittings
- AirPower 4mm Replacement Nipples
- AirPower 76~83mm Replacement Inflatable Tires Set

Grumania Jet Pipe Inlets

High quality Turbine Jet Pipe Inlet for Turbine Pipes. Improved airflow and performance.
Available for:
- 15N-30N Turbines
- 40N-80N Turbines
- 80N-160N Turbines

AirPower Brake Spares

Various spare parts for Airpower Wheels:
- 33mm Disk Brake Replacement Pads
- 33mm Pneumatic Brake Inflatable Rubber Seals
- AirPower Replacement 90 deg Air Fittings
- AirPower 4mm Replacement Nipples

JTM Oleo Replacement Springs

Set of 3 replacement springs for the JetTeng – JTM – Oleo trailing oleo struts for JTM’s Hawk and L-39.

New and to be released shortly at only 109 USD, the new HET-RC Flying Wing powered glider with a wingspan of 1.8m.

Available soon !!

The all new HET-RC L-39 Albatross for 90mm Fan units (or P-20 Turbine).

The model features:

• Epoxy composite pre-painted fuselage and stabs
• Full intake & exhaust ducting with NO cheater holes
• Balsa foam sheeted wings
• Laser Cut retract plywood mounts
• Clear Canopy
• Decal set
• Wing tip tanks

Specifications:

• Wingspan: 1118 mm (44”)
• Length: 1400 mm (55”)
• Flying Weight: 4000 grams

The Model is available in 2 colors. Breitling Jet Team Black as shown above and HPAT Colors ash shown below.

Retracts with Oleo Struts are available as option.

The MULTI SERVO Distribution can use one servo input signal to simultaneously drive up to four servos.

When using multiple servos to drive one control surface different setting states are display by LED.
Allows the use of a separate power supply/battery pack for the servos connected to the MSD.

Introducing the all new JetCat P100-RX:

• Compact outline and form factor
• Internal kerosene start
• Internal EGT sensor!
• Internal solenoids, only one fuel connection to the engine
• New “Bus-system” fuel pump.
  Eliminates necessity to adjust pump startup voltage!
• Single wiring connection from ECU to engine
• New miniature/lightweight ECU V10.0
• Battery: 2-cell LiPo or optional 3-cell LiFePo (e.g. A123)

This new design of the P100-RX incorporates an optimized
compressor/diffusor system, resulting in higher engine performance
and reliability.

The engine follows throttle commands almost without delay.

Size Comparison – P80SE / P100-RX / P-60

New ECU V10.0
The completely redesigned V10.0 ECU is three times smaller than the
V6.0 ECU, yet has all its proven capabilities and more at a weight of
only 26g !
The new ECU comprises a high speed digital power bus for control
and power supply of all engine peripherals (e.g. engine, fuel pump,
solenoids, smoke pump, lighting systems, etc. ) with a minimum of
wiring connections.
An on board precision pressure and ambient temperature sensor
allows for optimum engine control, independent to environmental
conditions.

L-39 Breitling Jet Team

Now in Stock: JTM’s latest L-39 Color Option
The JTM L-39 Albatros in the colors of the Breitling Jet Team is a high performance EDF Jet in full composite design for 90mm Fan units such as the Schuebeler DS-51 or WeMoTec Midi Fan Pro.

A turbine conversion to JetCat P-20, Lambert T25 or Wren 44 (see similar conversion done with the JTM Hawk) can be done easily. Please check with us on suitable turbines, pipes and accessories.
The model features a full composite fuselage and wing with retract hard points pre-installed in the nose and retract hatches pre-cut in the wing.
The model comes completely pre-painted with all decals applied and protected by a clear coat.
Further is the cockpit glued and all hatches are assembled and locks are installed in place. The Model features flaps.
This model is truly ARF with all the major work done for you.
Retracts and suitable scale oleo struts are available as option

Fox Hawk – 2010

The Fox-Composites BAE Hawk in 2010 Demo Colors is an affordable, light weight, full composite RC Jet for Turbine Power.
The prototype Hawk was initially powered by a PST 600, (54 size turbine). Later production models are now flying with various turbine configurations such as the Wren 44 or JetCat P60.

The Fox Hawk featured here includes a fully installed the turbine duct and conformal Tanks.
The model features full composite construction with molded flex hinged ailerons, flaps and rudder. A flying elevator including mechanic and mount is also included.
To further boost the scale appearance of this amazingly detailed jet a full scale cockpit is available

Rafale/Gripen Landing Gear Package

Airpower Hydraulic Oleo Landing Gear Combo Package suitable for Skymaster / X-Treme Rafale, Skymaster / X-Treme Saab JAS-39 Gripen, FBJets Rafale and JetLegend Saab JAS-39 Gripen.

Airpower Wheels

High performance model tire.
Inflatable tire with painted metal rim (white). Both tires come with precision ball bearings.
Tire is replaceable.

TamJets P20 Air Trap Tank

Super small Air Trap / Hopper Tank especially designed for small turbines such as the JetCat P20-SE or Lambert Micro Turbines.

1/8″ 8 color airline

Package of 8 different colored 1/8” Airlines with 6 feet each. Ideal for retract brake or gear door installations.

MAP Wing Tip Skid

How often did you strike your wing tip on your brand new airplane?
It just happen so often.
Here is the wing skid that protects your wing tip. This is not all.
It was design to be removable. Some don’t like to show their plane with wing skid on static display. You can remove skids and put in your tool box.

Wing Tip Skid Replacements

Package of 4 replacement wing tip skids for the MAP Wing Tip Skid Kit.

RC-Warbirds Desktop Wallpaper

From January 2011 we will bring you a new PC and Mobile Phone Wallpaper every month.
January 2011 was kicked off by a picture of a F9F Cougar we took during the 2007 TopGun event in Lakeland Florida.
Our February 2011 wallpaper features 2 true warbirds, a P51 Mustang and a P47 Thunderbolt. This picture was taken by us during the 2010 Jet & Warbird meet of the MFC Dachau in the south of Germany. Make sure to check out the video of this event on our youtube channel.
Although we are snapping pictures like crazy, we would be happy to feature your shot as one of our monthly pictures. Drop us an email to send us your shot !

F-16 90mm Fan

The 3rd Jet for a 90mm Fan unit from HET-RC.

Unlike the other 2 models (Sniper 90 and F-18), the HET-RC F-16 features a epoxy fiberglass fuselage resulting in a lighter body and more chip resistant surface.
The F-16 is a available in 4 distinct color schemes, Edwards AFB, General Dynamics, Gray and Thunderbirds.
The model is fully prepared for a retractable landing gear (see options below) and allows the installation of working gear doors.
Powered by 8-10S and with its included wingtip missiles, this model will be the star at every flying site.

Also available in Edwards AFB Colors

Also available in Gray Color

Me-163 Komet

The HET Me163 Komet is a Fiberglass Model with Foam/Balsa Wings powered by a propeller.
A powerful brushless motor in the nose of the plane combined with pylon prop allows this sleek jet to reach high speeds (see our FOX Composites Me-163 Video with speeds in excess of 320km/h or 200mph).
The model has enough space to accommodate LiPo packs of various sizes allowing either 3s or 4s configurations with motors in the range of 300 to 900 Watt power.

HET 120A ESC

A high performance ESC for brushless powered EDF Jets, sport and aerobatic planes and gliders.
For 2S-6S LiPo
The ESC features easy programming via transmitter or the optional available programming card.

Grumania Custom Pipes

High Quality Grumania Jet Models Pipe.
Each Jet Pipe is custom made to order for your specific jet. Simply let us know how long your jet pipe needs to be and for what engine you require it and we will do the rest.
Each pipe comes with a intake funnel for better heat shielding.

AirPower High Flow UAT

High Flow Air Trap Hopper Tank with 150ml volume for large turbine models. Suitable for turbines with 160N and more. (JetCat P160, P200….)

Bulkhead Fuel Barb Fitting

Bulkhead Fuel Fitting for Turbine Jets, Gasoline and Nitro Powered Model planes. Allows for easy connection of fuel lines though bulk heads.
Ideal suitable to connect overflow and taxi tanks.
Fits ID 1/8” Tubing .

Airpower Disc Brake

AirPower Models 25mm Pneumatic Disc Brake Set For 50-76mm Wheels.
Suitable for AirPower Wheels up to 76mm diameter.

AirPower Offset Gear Door Hinge

These offset gear door hinges make gear door installation a snap.
Multiple cylinder attach points and large mounting feet.

10 hinges per pack !

Gear & Door Valve

Airpower Gear and Door valve suitable for all pneumatic-operated (air) retractable Landing gears and gear door cylinders.
Can be operated with mini or micro size servos.

Rubber Wheels

Light Weight, low air drag and bounce aircraft rubber wheels.
Available in the following sizes: 1”, 1.5”, 1.75”, 2”, 2.5”, 3”

LiPo Balancer Charger

The perfect Lipo charger for your startbox or just to be placed inside the car for emergency recharging of small flight packs and TX/RX Packs.
Specifications:
- Charges 1-5 LiPo or Li-Ion Cells
- Balancer in-build
- Charge current from 0.1A to 5A in 0.1A steps
- Input: 11-15V DC
- LCD Display shows charging data
- Automatic polarity check

Gear Door Set (small)

Add realism to your model plane with full working retract doors.
This set includes everything you need to add working retract doors to your jet. The set includes 3 air cylinders with 12mm stroke, offset gear door hinges for 3 gear doors, airvalve mount and air valve to toggle the door movement.
The system will be connected to your existing retract air circuit.Door open action is slvaed to the retract valve so that the doors open at the same time as the gear is deployed. Door close function is independently activated by the included valve which need to be driven by a separate servo.
The perfect match for Tamjets 1/12 F-16, Aeronaut Rafale, JTM BAE Hawk or Jet Teng L-39 Albatros

HET F-16 90mm Retracts Set

The HET-RC F-16 Retracts are specially designed for the HET-RC F-16 Fighting Falcon composite EDF Jets. The set comes complete with air tank, hose and valves. These retracts come with oleo struts mounts suitable for the optional available HET-RC F-16 Oleo Struts.

HET F-16 90mm Oleo Set

Oleo Struts specially designed for the HET-RC F-16 EDF Jet.
Add scale realism in looks and function to your model air plane. Whether you use fixed or retractable landing gears, these struts can be fitted. Helps to smoothen landings and improves ground handling, especially on grass fields. Package includes 2 main gear oleo units with wheels and one nose oleo strut with mounted wheel

Coming Soon: AirPower PDS-620A Power Distribution System

AirPower PDS-620A Power Distribution Systems
Specification

• Operating voltage : 5.0 to 9.0 Volts for DC
• Power supply : 2*2-cell LiPo batteries, 7.4 Volt
• Output voltage :
• Receiver : 6V
• Servo : 5.0V / 5.4V / 6.0V / 7.0V / ByPass
• Output current :
• Receiver : 5.0 A (succession stabilized)
• Servo : 20.0 A (succession stabilized)
• Peak current :
• Servo – 50 A ( servo side, 15 sec.)
• Receiver – 10A (Rx. side, 15 sec.)
• Servo sockets: 15 sockets, 6 channels
• Temperature range: -20 to +85 (centigrade)
• Dimensions : L 76 x W 60 x H 25 mm
• Weight: 130g

Coming soon…….. 2011′ 02′