November 2011 Desktop Wallpaper

November 2011 features a picture taken during one of our trips to Nusa Jaya Malaysia.
Mr. Hengs, amazing Twin turbine powered SU-27 shortly before the maiden flight..

JTM ViperJet HPAT (red)

Just released, the new Jet Teng (JTM) full composite Viper Jet in 5 amazing color schemes.
The Viper Jet is a jet aircraft designed and produced by Viper Aircraft Corporation in kit form for homebuilding. It is a conventional, low-wing monoplane with swept wings and tail and two seats in tandem under a bubble canopy. The jet intakes are located at the sides of the fuselage and the tricycle undercarriage is retractable. Construction throughout is of composite materials

JTM ViperJet HPAT (green)

The JTM ViperJet in the colors of the High Performance Aircraft Training school (HPAT) is a high performance EDF Jet in full composite design for 90mm Fan units such as the Schuebeler DS-51 or WeMoTec Midi Fan Pro.
A turbine conversion to JetCat P-20, Lambert T25 or Wren 44 (see video below) can be done easily. Please check with us on suitable turbines, pipes and accessories.
The model features a full composite fuselage and wing with retract hard points pre-installed in the nose and retract hatches pre-cut in the wing.
The model comes completely pre-painted with all decals applied and protected by a clear coat.
Further is the cockpit glued and all hatches are assembled and locks are installed in place.
This model is truly ARF with all the major work done for you. Retracts and suitable scale oleo struts are available as option.

JTM ViperJet Swiss

Pack contents:
Fully painted and finished glass fiber fuselage, fully assembled vertical fin and pre-installed ducting, clear canopy with pre-installed lock, one-piece fully painted and finished glass fiber wing with aileron, flap and retract hatches, exhaust ducting sheet, small parts, hardware pack, gear door covers.

JTM ViperJet White/Red

JTM Viper RC functions:
- Ailerons
- Elevator
- Throttle
- Flaps
- Rudder
- Gear
- Nose gear steering
- Brakes (optional)

JTM ViperJet Bronze/Black

Specifications:
Type…………………………: ARF
Material……………………..: Full Composite (glass/carbon)
Fan size……………………..: 90mm
Wing Span…………………: 1410mm (55.5”)
Length………………………: 1280mm (50.5”)
For EDF
Recommended Fan………: DS-51, TJ90, SM90,HET 9305-700
Recommended Motor……: Lehner 1940-12 HA (8s),Het 700, NeuMotors 15xx
For Turbine
Recommended Turbine…: JetCat P-20, Lambert T25, Wren44
Radio………………………..: 5-7 channel, 5-9 servo

Full size Information:
The Viper Jet is a jet aircraft designed and produced by Viper Aircraft Corporation in kit form for homebuilding. It is a conventional, low-wing monoplane with swept wings and tail and two seats in tandem under a bubble canopy. The jet intakes are located at the sides of the fuselage and the tricycle undercarriage is retractable. Construction throughout is of composite materials.

Product Information:
The JTM ViperJet in the colors of the High Performance Aircraft Training school (HPAT) is a high performance EDF Jet in full composite design for 90mm Fan units such as the Schuebeler DS-51 or WeMoTec Midi Fan Pro.
A turbine conversion to JetCat P-20, Lambert T25 or Wren 44 (see video below) can be done easily. Please check with us on suitable turbines, pipes and accessories.
The model features a full composite fuselage and wing with retract hard points pre-installed in the nose and retract hatches pre-cut in the wing.
The model comes completely pre-painted with all decals applied and protected by a clear coat.
Further is the cockpit glued and all hatches are assembled and locks are installed in place.
This model is truly ARF with all the major work done for you.
Retracts and suitable scale oleo struts are available as option.

Pack contents:
Fully painted and finished glass fiber fuselage, fully assembled vertical fin and pre-installed ducting, clear canopy with pre-installed lock, one-piece fully painted and finished glass fiber wing with aileron, flap and retract hatches, exhaust ducting sheet, small parts, hardware pack, gear door covers.

RC functions:
- Ailerons
- Elevator
- Throttle
- Flaps
- Rudder
- Gear
- Nose gear steering
- Brakes (optional)

Specifications:
Type…………………………: ARF
Material……………………..: Full Composite (glass/carbon)
Fan size……………………..: 90mm
Wing Span…………………: 1410mm (55.5”)
Length………………………: 1280mm (50.5”)
For EDF
Recommended Fan………: DS-51, TJ90, SM90,HET 9305-700
Recommended Motor……: Lehner 1940-12 HA (8s),Het 700, NeuMotors 15xx
For Turbine
Recommended Turbine…: JetCat P-20, Lambert T25, Wren44
Radio………………………..: 5-7 channel, 5-9 servo

The HET L-39 Albatros is a high performance EDF Jet with fiberglass fuselage and foam/balsa wings suitable for 90mm Fan units such as the Schuebeler DS-51 or WeMoTec Midi Fan Pro.
A turbine conversion to JetCat P-20 or Lambert T25 (see similar conversion done with the JTM Hawk) can be done. Please check with us on suitable turbines, pipes and accessories.
The model features a fiberglass fuselage and foam/balsa wings with retract hard points pre-installed in the nose and retract hatches.
The model comes completely pre-painted.
The Model features flaps.
This model is truly ARF with all the major work done for you.
Retracts and suitable scale oleo struts are available as option

Me-262 (olive)

The brand new HET-RC Me-262 is a high performance Jet for TWIN EDF units such as the WeMoTec Mini Fan 480 or the HET-RC 6904 and 2x powerful brushless motors such as the HET-RC Typhoon 2W, 3W or 2W-20 EDF. The ARF kit features a olive green painted fiberglass fuselage with balsa sheeted foam wings. This new revised version of the Me262 now features retract gear mounting points which are the perfect match for the optional available electric retracts system and oleo strut set.

Messerschmitt Me-262 (gray)

The Messerschmitt Me 262 Schwalbe (German: “Swallow”) was the world’s first operational turbojet fighter aircraft. It was produced in World War II and saw action starting in 1944 in bomber/reconnaissance and fighter/interceptor roles. It was officially named Schwalbe because the swallow, when in a dive, is one of the fastest birds known. German pilots nicknamed it the “Turbo,” while the Allies called it the “Stormbird.” While the Me 262 had a negligible impact on the course of the war (approximately 150 Allied aircraft losses for 100 Me 262 losses), its design had a strong influence on postwar aircraft development.

HET Me 163 Red EDF

The HET Me163 Komet is a Fiberglass Model with Foam/Balsa Wings powered by a 70mm EDF unit.
The model has enough space to accommodate LiPo packs of various sizes allowing either 3s or 4s configurations
Speed freak – beware !!!!!

Stumax SM80-45

The SM80-45 EDF system is based on the highly successful SM89-45 and SM110 multiblade rotor design. Specially designed for the new 80mm fan Jets out there (e.g. eFlite Habu)
Unlike traditional EDF units, the SM80-45 features a 11 blade rotor for improved static thrust and sound. Turbine like sound in an small scale EDF model is a dream come through thanks to this fan.

Martin Baker Ejection Seat Kit 1/10th

Grumania Martin Baker Ejection Seat Kit in 1/10th scale. Although the ejection seat was originally made for the Grumania F 100, it fits other jets of similar size very well. The Kit consists of moulded plastic parts that can easily be assembled using CA glue.The seat is extremely light.
Sizes (approx.):
Height…………..: 115mm
Depth……………: 65mm
Width……………: 58mm

Trailing Mini Oleo Strut Set

Add scale realism in looks and function to your model air plane. Whether you use fixed or retractable landing gears, these struts can be fitted. Helps to smoothen landings and improves ground handling, especially on grass fields. Package includes 3 pieces of trailing oleo struts (2x mains, 1x nose) and wheels.

Advanced Electronic Retract Set OLEO

Electric retract Set with aluminum oleo struts – suitable for EDF Jets and planes up to 2.5kg
The electric retract set features:
- 3 seconds overcurrent/jamming protection
- Auto recovery after overcurrent and jamming protection
- Smart circuit to prevent retract unit from accidentally
retracting when powering on the radio (even if the retract switch is set to retract up)
- Includes fitting to twist the strut 90 degrees when retracted
- Suitable voltage 4.8-6V
- 85gram retract loading – Working current 0.1-0.3A

Advanced Electronic Retract System Set

Electric retract Set with aluminum wire struts – suitable for EDF Jets and planes up to 2.5kg
The electric retract set features:
- 3 seconds overcurrent/jamming protection
- Auto recovery after overcurrent and jamming protection
- Smart circuit to prevent retract unit from accidentally
retracting when powering on the radio (even if the retract switch is set to retract up)
- Includes fitting to twist the strut 90 degrees when retracted
- Suitable voltage 4.8-6V
- 85gram retract loading – Working current 0.1-0.3A

Fox Hawk Jet Pipe

High Quality Grumania Jet Models Pipe for the Fox Composites Bae Hawk. Suitable for turbines from 40-80N.

www.youtube.com/watch?v=I3jE-PXV-68

The Airpower MSD-400 Multi Servo Distribution System can used to use one servo input signal to simultaneously drive up to four servos.
The MSD-400 allows for accurate adjustment of servos when driving one common control surface with up to 4 servos. The servo and receiver power supply can be separated by using a separate battery pack for the servos.
Specifications:
Size………………………….: 46mm L x 11.10mm H x 25.80mm W
Weight………………………: 10 gram
Current Draw……………..: 20 mA
Operating Voltage………..: 4.8V~9.0V

Airpower Key Chain

Airpower Transmitter Key Chain

AirPower RA-250 Wire Adapter (3/16”)

Airpower RA-250 Trunion Adapter for 3/16” Wire Struts
Package of 2

AirPower RA-250 Wire Adapter (5mm)

Airpower RA-250 Trunion Adapter for 5mm Wire Struts
Package of 2

AirPower Replacement Air Fittings

AirPower Replacement Air Fittings – M3 thread.
These are OEM replacement airline nipples for all AirPower & Skymaster Retracts & Brakes.
Contents:
5x Replacement Nipples (M3)

25mm Disk Brake Replacement Pads

Package of 4 25mm Disk Brake Replacement Pads for AirPower 25mm Disk Brakes (BK-2500)

AirPower 70~75mm Replacement Inflatable Tires Set

Inflatable replacement tire for all Airpower and Skymaster 70-75mm (2 3/4” – 3”) Wheels.
Package includes 2 tires.

AirPower 57~63mm Replacement Inflatable Tires Set

Inflatable replacement tire for all Airpower and Skymaster 57-63mm (2 1/4” – 2 1/2”) Wheels.
Package includes 2 tires.

AirPower 50~55mm Replacement Inflatable Tires Set

Inflatable replacement tire for all Airpower and Skymaster 50-55mm (2” – 2.15”) Wheels.
Package includes 2 tires.

AirPower 57~63mm Replacement Inflatable Tires Set

Inflatable replacement tire for all Airpower and Skymaster 50-57mm – 63mm (2.25” – 2.5”) Wheels.
Package includes 2 tires.

With the size of a model usually powered by kerosene turbines, a composite molded fuselage and balsa wings and the simplicity and lower cost of an EDF Jets, the SAPAC BAE Hawk 100mm is the perfect entry into large scale rc jet models.
The model is designed for 100mm EDF Units such as the Stumax SM100 or TamJets TJ100. Please see the drop down menu below for available power options.

SAPAC T-45 Goshawk 100mm

With the size of a model usually powered by kerosene turbines, a composite molded fuselage and balsa wings and the simplicity and lower cost of an EDF Jets, the SAPAC T-45 100mm BAE Hawk is the perfect entry into large scale rc jet models. The model is designed for 100mm EDF Units such as the Stumax SM100 or TamJets TJ100. Please see the drop down menu below for available power options.
Pack contents:
Assembly instructions in English, pre-painted fiberglass fuselage, covered balsa wings, molded fin and balsa tail surfaces, small items, clear canopy, linkage hardware pack including nylon control horns, PVC and optional composite ducting and decal sheet

JetCat Turbine Mount “Standard”

JetCat Turbine Mount “Standard” for JetCat P-80 to P-160 Engines

JetCat Fuel & Propane Valve

JetCat Fuel & Propane Shut-off-valve (solenoid) for JetCat and other turbines.

JetCat Fuel & Propane Filter

JetCat Fuel and Propane Filter for JetCat (and other) Turbines.

JetCat P20-SE Turbine

Introducing the new JetCat P20-SE, the baby turbine from JetCat.
The JetCat P20-SE is the long awaited solution for small EDF Jet conversions. With 2.4kg thrust, this turbine can power any 90size EDF Jet (examples: JTM Hawk, JTM L-39, TamJets 1/12th scale F-16…..).
The engine follows throttle commands almost without delay. The P20-SE comes with the new V10 ECU. Not only does it feature an incredible small size & weight, the new bus system makes installing your components a breeze. With one cable running from ECU to turbine (instead of 2 with the older versions) and one cable running from ECU to pump and on to the 2 solenoid block.

Featuring JetCat’s new fully digital “bus” electronic control system, the new generation of RX series JetCat turbines reduce the wiring and tubing to a minimum, making installation easier.

The temperature sensor is installed internally, but still can be replaced if necessary. The valves are fully integrated inside the turbine front housing, so only a single tube connection from the pump to the turbine is necessary. Additionally the electrical connection from the turbine to the ECU, also involves only a single PowerBus lead.

The new light weight and small V10.0 JetCat ECU (26g and 2/3rds size) require only the receiver (1 or 2 channel operation) and the fuel pump to be connected. All of the latest options e.g. ECU V6.0 GSU connection, GPS and Airspeed sensor input/output, Smoke control will still be available.
The power supply is provided by a 3S 2100mAh LiFePO4 battery. This not only powers the ECU and fuel pump, but also all optional accessories connected to the bus system, such as the JetCat Smoke Pump and or LCU (lighting control Unit).

Alternatively, the V10.0 ECU can be supplied for operation with a 2S/3S Li-po or 6-8 cell Ni chemistry battery.
The V10.0 ECU also has a built-in, precision air pressure and temperature sensor which intelligently adjusts to the current environmental conditions. This also eliminates the setting of the pump start voltage. The engine starts and runs on kerosene.

The weight of the JetCat is P140RX-1580g. The maximum thrust is 142N @ 125,000 rpm. With a diameter of 112mm and an overall length of 320mm the size matches closely the P120SX size.

The HET L-39 Albatros is a high performance EDF Jet with fiberglass fuselage and foam/balsa wings suitable for 90mm Fan units such as the Schuebeler DS-51 or WeMoTec Midi Fan Pro.
A turbine conversion to JetCat P-20 or Lambert T25 (see similar conversion done with the JTM Hawk) can be done. Please check with us on suitable turbines, pipes and accessories.
The model features a fiberglass fuselage and foam/balsa wings with retract hard points pre-installed in the nose and retract hatches.
The model comes completely pre-painted.
The Model features flaps.
This model is truly ARF with all the major work done for you.

HET Flying Wing 1.8m + Prop Yellow

The HET Flying Wing in yellow color is a 1.8 meter wingspan powered glider for slope, ridge and thermals.
Combined with a brush less motor and the included 10×6 folding prop and spinner, the HET Flying Wing is capable of powerful climbs.
The HET Flying Wing features a fiberglass fuselage and foam/balsa sheeted wings. The Model completely build and requires a minimum of assembly.
With it’s large speed envelope the Wing is suitable for beginners as well as experienced pilots looking for a aerobatic glider with good wind penetration.
The Wing can be build as glider or powered glider.

HET F-16 Thunderbirds

The 3rd Jet for a 90mm Fan unit from HET-RC.
Unlike the other 2 models (Sniper 90 and F-18), the HET-RC F-16 features a epoxy fiberglass fuselage resulting in a lighter body and more chip resistant surface.
The F-16 is a available in 4 distinct color schemes, Edwards AFB, General Dynamics, Gray and Thunderbirds.
The model is fully prepared for a retractable landing gear (see options below) and allows the installation of working gear doors. Powered by 8-10S and with its included wingtip missiles, this model will be the star at every flying site.

AirPower Air Control System Kit – PRO

A great way to save some $$$. This Air Control System Kit Pro supports any Air Retract, Door and brake system
Complete with:
- 2x Airpower EV-2U Dual Action Valves
- 1x AirPower EV-1U – Brake Valve
- 1x Digit Dual Air Gauge
- 2x Air System Fill Valve with Chuck
- 10x Barbed Airline Fittings
- 4x Airpower 1/8″ / 3 mm Air Tubing Mount
- 10meter of Airpower 1/8″ Air Line
- 2x Airpower Air Tanks
this complete installation kit leaves no desires open.

HET Retract Set 90size (L-39)

The HET-RC L-39 Retracts are specially designed for the HET-RC L-39 Albatros composite EDF Jets. The set comes complete with air tank, hose and valves. These retracts come with oleo struts mounts suitable for the optional available HET-RC L-39 Oleo Struts.

HET L-39 Oleo Struts

Oleo Struts specially designed for the HET L-39 90 size EDF Jet. Add scale realism in looks and function to your model air plane. Whether you use fixed or retractable landing gears, these struts can be fitted. Helps to smoothen landings and improves ground handling, especially on grass fields. Package includes 2 trailing main gear oleo units with wheels and one trailing nose oleo strut with fork mounted wheel

HET Flying Wing 1.8m + Prop Red

The HET Flying Wing in yellow color is a 1.8 meter wingspan powered glider for slope, ridge and thermals.
Combined with a brush less motor and the included 10×6 folding prop and spinner, the HET Flying Wing is capable of powerful climbs.
The HET Flying Wing features a fiberglass fuselage and foam/balsa sheeted wings. The Model completely build and requires a minimum of assembly.
With it’s large speed envelope the Wing is suitable for beginners as well as experienced pilots looking for a aerobatic glider with good wind penetration.
The Wing can be build as glider or powered glider.

Festo Y-Tube fitting

Festo Y Fitting for 3mm and 4mm tubing.
Suitable for Air, Gas and Kerosene.

Festo Tee Tube fitting

Festo Tee Fitting for 3mm and 4mm tubing.
Suitable for Air, Gas and Kerosene.

Festo PUN-H Tubing

Festo 3mm and 4mm PUN-H tubing.
Suitable for Air, Gas and Kerosene.

Offer valid till July 31st or till stocks last.

Click here for details: Airbrush Color

Click here for details: Gray Color

July 2011 Desktop Wallpaper

July 2011 features another photo taken during the 2008 TopGun Event in Lakeland Florida.
This time we feature a BVM Ultra Bandit captured during a knife edge flyby.

AirPower RA-215 Retract Main and Nose

AirPower Models are pleased to present their all new retract units.
Made from Anodised aluminium these units feature air up and air down operation and are intended to use in models from 9kg / 20lbs up to 20kg / 45 lbs in weight. Designed to be retro fitted in many of today’s sport models these units are able to withstand operation from grass and tarmac fields.
The main pivot block is made from high quality 7075 aluminium and machined to accept a 1/2” oleo strut. Retained in a clamp type mount that ensures a secure fixing with less chance of the leg rotating. The pivot pin is deliberately oversized in a effort to make all three units more rugged. The nose retract come as standard with the steering mechanism pre fitted as well as the straightening spring, although this can easily be removed and replaced with a 1/2 inch Oleo leg.
The RA-215 are available as singular units or as a complete kit of 3 units.

AirPower RA-250 Retract Main and Nose

AirPower’s RA-250 retract offers an ultra low profile that is only 27mm in height. This retract is able to take a 7/16″ diameter Strut. Also available is a standard gear wire in 3/16″ for Main Gears.
The Retract is constructed out of high quality aircraft grade 6061-T6 & 7075 aluminum. The RA-250 Retracts is designed to replace other manufacturers retract systems and are the strongest retractable landing gear in the industry for this size.

Grumania FOD for JetCat P20-SE

This FOD screen is special design for use with a JetCat P20-SE or similar size turbine engine.

Tamjets E-flite Spark Retract Set

Full electric retract set for the CARF Spark.
The Tamjets / E-flite retract set is based on the original E-flite 60 – 120 Tricycle Electric Retracts set. However in order to support the weight of the Spark and make the retract unit more durable in general, Tamjets replaced the original E-flite trunion with an stronger unit machined out of high strength aluminum.
In addition this new trunion is now capable of utilizing the proven Tamjets trailing oleo struts for the CARF Spark.
The set further includes a set of Tamjet TJ Pro-Lite wheels and brakes to complete the combo.

AirPower 5mm Wire Struts Wheels & Brake Set

High performance inflatable model tire with pneumatic brake and 5mm Wire strut + adapter.
Inflatable tire with metal rim. The tires comes with precision ball bearings (6mm).
Tire is replaceable.
Suitable for all retract mechanics with 5mm wire adapter (wire strut is included in the set)

AirPower Wheel Spares

Various spare parts for Airpower Wheels:
- AirPower 70~85mm Wheel Rubber Seals
- AirPower 70~85mm Inflation Seals
- AirPower Replacement 90 deg Air Fittings
- AirPower 4mm Replacement Nipples
- AirPower 76~83mm Replacement Inflatable Tires Set

Grumania Jet Pipe Inlets

High quality Turbine Jet Pipe Inlet for Turbine Pipes. Improved airflow and performance.
Available for:
- 15N-30N Turbines
- 40N-80N Turbines
- 80N-160N Turbines

AirPower Brake Spares

Various spare parts for Airpower Wheels:
- 33mm Disk Brake Replacement Pads
- 33mm Pneumatic Brake Inflatable Rubber Seals
- AirPower Replacement 90 deg Air Fittings
- AirPower 4mm Replacement Nipples

JTM Oleo Replacement Springs

Set of 3 replacement springs for the JetTeng – JTM – Oleo trailing oleo struts for JTM’s Hawk and L-39.

New and to be released shortly at only 109 USD, the new HET-RC Flying Wing powered glider with a wingspan of 1.8m.

The all new HET-RC L-39 Albatross for 90mm Fan units (or P-20 Turbine).

The model features:

• Epoxy composite pre-painted fuselage and stabs
• Full intake & exhaust ducting with NO cheater holes
• Balsa foam sheeted wings
• Laser Cut retract plywood mounts
• Clear Canopy
• Decal set
• Wing tip tanks

Specifications:

• Wingspan: 1118 mm (44”)
• Length: 1400 mm (55”)
• Flying Weight: 4000 grams

The Model is available in 2 colors. Breitling Jet Team Black as shown above and HPAT Colors ash shown below.

Retracts with Oleo Struts are available as option.

The MULTI SERVO Distribution can use one servo input signal to simultaneously drive up to four servos.

When using multiple servos to drive one control surface different setting states are display by LED.
Allows the use of a separate power supply/battery pack for the servos connected to the MSD.

Introducing the all new JetCat P100-RX:

• Compact outline and form factor
• Internal kerosene start
• Internal EGT sensor!
• Internal solenoids, only one fuel connection to the engine
• New “Bus-system” fuel pump.
  Eliminates necessity to adjust pump startup voltage!
• Single wiring connection from ECU to engine
• New miniature/lightweight ECU V10.0
• Battery: 2-cell LiPo or optional 3-cell LiFePo (e.g. A123)

This new design of the P100-RX incorporates an optimized
compressor/diffusor system, resulting in higher engine performance
and reliability.

The engine follows throttle commands almost without delay.

Size Comparison – P80SE / P100-RX / P-60

New ECU V10.0
The completely redesigned V10.0 ECU is three times smaller than the
V6.0 ECU, yet has all its proven capabilities and more at a weight of
only 26g !
The new ECU comprises a high speed digital power bus for control
and power supply of all engine peripherals (e.g. engine, fuel pump,
solenoids, smoke pump, lighting systems, etc. ) with a minimum of
wiring connections.
An on board precision pressure and ambient temperature sensor
allows for optimum engine control, independent to environmental
conditions.

Now in Stock: JTM’s latest L-39 Color Option
The JTM L-39 Albatros in the colors of the Breitling Jet Team is a high performance EDF Jet in full composite design for 90mm Fan units such as the Schuebeler DS-51 or WeMoTec Midi Fan Pro.

A turbine conversion to JetCat P-20, Lambert T25 or Wren 44 (see similar conversion done with the JTM Hawk) can be done easily. Please check with us on suitable turbines, pipes and accessories.
The model features a full composite fuselage and wing with retract hard points pre-installed in the nose and retract hatches pre-cut in the wing.
The model comes completely pre-painted with all decals applied and protected by a clear coat.
Further is the cockpit glued and all hatches are assembled and locks are installed in place. The Model features flaps.
This model is truly ARF with all the major work done for you.
Retracts and suitable scale oleo struts are available as option

Fox Hawk – 2010

The Fox-Composites BAE Hawk in 2010 Demo Colors is an affordable, light weight, full composite RC Jet for Turbine Power.
The prototype Hawk was initially powered by a PST 600, (54 size turbine). Later production models are now flying with various turbine configurations such as the Wren 44 or JetCat P60.

The Fox Hawk featured here includes a fully installed the turbine duct and conformal Tanks.
The model features full composite construction with molded flex hinged ailerons, flaps and rudder. A flying elevator including mechanic and mount is also included.
To further boost the scale appearance of this amazingly detailed jet a full scale cockpit is available

Rafale/Gripen Landing Gear Package

Airpower Hydraulic Oleo Landing Gear Combo Package suitable for Skymaster / X-Treme Rafale, Skymaster / X-Treme Saab JAS-39 Gripen, FBJets Rafale and JetLegend Saab JAS-39 Gripen.

Airpower Wheels

High performance model tire.
Inflatable tire with painted metal rim (white). Both tires come with precision ball bearings.
Tire is replaceable.

TamJets P20 Air Trap Tank

Super small Air Trap / Hopper Tank especially designed for small turbines such as the JetCat P20-SE or Lambert Micro Turbines.

1/8″ 8 color airline

Package of 8 different colored 1/8” Airlines with 6 feet each. Ideal for retract brake or gear door installations.

MAP Wing Tip Skid

How often did you strike your wing tip on your brand new airplane?
It just happen so often.
Here is the wing skid that protects your wing tip. This is not all.
It was design to be removable. Some don’t like to show their plane with wing skid on static display. You can remove skids and put in your tool box.

Wing Tip Skid Replacements

Package of 4 replacement wing tip skids for the MAP Wing Tip Skid Kit.